esphome:
  name: garten-bus-controller

esp32:
  board: esp32-poe
  framework:
    type: arduino

# Enable logging
#logger:

# Enable Home Assistant API
api:
  encryption:
    key: !secret api_encryption_key

ota:
  password: !secret ota_password


external_components:
  - source:
      type: git
      url: "https://github.com/andyboeh/esphome-dmx512"
      ref: master


#external_components:
#  - source:
#      type: local
#      path: my_components

#wifi:
#  ssid: "WLAN"
#  password: !secret wifi_password
#
#  # Enable fallback hotspot (captive portal) in case wifi connection fails
#  ap:
#    ssid: "Garten Bus Controller Hotspot"
#    password: !secret ota_password
#captive_portal:

ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO17_OUT
  phy_addr: 0
  power_pin: GPIO12

uart:
  #- id: "uart_dmx"
    #rx_pin: 0
    #tx_pin: 
      #number: 1 # the pin where the transmission happens connected to tx (not reversed)
      #allow_other_uses: true
    #stop_bits: 2
    #baud_rate: 250000
  - id: uart_relays
    rx_pin: 2
    tx_pin: 3 
    baud_rate: 9600
  - id: "uart_oxilife"
    rx_pin: 4
    tx_pin: 5
    baud_rate: 19200
    stop_bits: 1
    parity: NONE

modbus:
  - uart_id: "uart_relays"
    id: "modbus_relays"
  - uart_id: "uart_oxilife"
    id: "modbus_oxilife"

modbus_controller:
  - modbus_id: "modbus_relays"
    id: "relayboard32"
    address: 0x1
    update_interval: "60s"
  - modbus_id: "modbus_relays"
    id: "relayboard8_with_inputs"
    address: 0x2
    update_interval: "1s"
  - modbus_id: "modbus_oxilife"
    id: "oxilife"
    address: 0x1
    update_interval: "1s"
  

packages:
  # ------------ Relays of 32-Relay board ----
  relay01: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-beete-nordwest"
      dev_addr: 0x1
      register_addr: 0x01
  relay02: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-beet-west"
      dev_addr: 0x1
      register_addr: 0x02
  relay03: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-sprinkler-westen"
      dev_addr: 0x1
      register_addr: 0x03
  relay04: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-giessanlage-vorne"
      dev_addr: 0x1
      register_addr: 0x04
  relay05: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-sprinkler-sud"
      dev_addr: 0x1
      register_addr: 0x05
  relay06: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-beet-sued"
      dev_addr: 0x1
      register_addr: 0x06
  relay07: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "ventil-brunnen-in-zisterne"
      dev_addr: 0x1
      register_addr: 0x07
  #--- obere reihe
  relay29: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "poolpumpe-speed3"
      dev_addr: 0x1
      register_addr: 29
  relay30: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "poolpumpe-speed2"
      dev_addr: 0x1
      register_addr: 30
  relay31: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "poolpumpe-speed1"
      dev_addr: 0x1
      register_addr: 31
  relay32: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard32
      name: "poolpumpe-speed-off"
      dev_addr: 0x1
      register_addr: 32

# ------------ Relays of 8-Relay board ----
  b2relay1: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard8_with_inputs
      name: "garten_relayboard8_switch1"
      dev_addr: 0x2
      register_addr: 0x1
  b2relay2: !include
    file: "modbus_relay.yaml"
    vars:
      cid: relayboard8_with_inputs
      name: "garten_relayboard8_switch2"
      dev_addr: 0x2
      register_addr: 0x2

# Controls input output relationship
#   0 no relationship
#   1 self-locking
#   2 interlocking
#   3 momentary
# commented out for now, because it sends all the time
#number:
#  - platform: modbus_controller
#    modbus_controller_id: relayboard8_with_inputs
#    name: "relayboard8-input-output-relationship"
#    value_type: U_WORD
#    address: 0x00fd
#    min_value: 0
#    max_value: 3
#    skip_updates: true


#dmx512:
#  id: dmx1
#  uart_id: uart_dmx
#  tx_pin:
#    number: 1
#    allow_other_uses: true
#  uart_num: 0
#  periodic_update: true

# ----------------------- Oxilife ------------------------------

sensor:
  #- platform: modbus_controller
  #  modbus_controller_id: oxilife
  #  id: oxilife_ionization_current 
  #  name: Ionization Strom
  #  value_type: U_WORD
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_hidro_current 
    name: Oxilife Hydrolyse 
    state_class: measurement
    device_class: POWER_FACTOR
    icon: mdi:percent
    address: 0x0101
    register_type: read
    value_type: U_WORD
    unit_of_measurement: "%"
    filters:
      - multiply: 0.1
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_ph
    name: Oxilife pH
    state_class: measurement
    icon: mdi:ph
    address: 0x0102
    register_type: read
    value_type: U_WORD
    accuracy_decimals: 2
    filters:
      - multiply: 0.01
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_redox_level 
    name: Oxilife Redox Level
    state_class: measurement
    icon: mdi:atom
    address: 0x0103
    register_type: read
    value_type: U_WORD
    unit_of_measurement: "mV"
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_clorine_ppm 
    address: 0x0104
    register_type: read
    value_type: U_WORD
    internal: true
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_conductivity
    address: 0x0105
    register_type: read
    value_type: U_WORD
    internal: true
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_temperature
    name: Pool Temperatur
    device_class: TEMPERATURE
    state_class: measurement
    address: 0x0106
    register_type: read
    value_type: U_WORD
    unit_of_measurement: "°C"
    accuracy_decimals: 1
    filters:
      - multiply: 0.1
  # pH status
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife pH Status Alarm
    id: oxilife_ph_status_alarm
    address: 0x0107
    register_type: read
    value_type: U_WORD
    bitmask: 0x000F
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Polarization A Time
    address: 0x0214
    register_type: read
    value_type: U_DWORD
    device_class: DURATION
    state_class: total_increasing
    unit_of_measurement: "s"
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Polarization B Time
    address: 0x0216
    register_type: read
    value_type: U_DWORD
    device_class: DURATION
    state_class: total_increasing
    unit_of_measurement: "s"
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Runtime Polarity Changes
    address: 0x0216
    register_type: read
    value_type: U_DWORD
    state_class: total_increasing
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay State
    id: oxilife_raw_relays
    address: 0x010E
    register_type: read
    value_type: U_WORD

binary_sensor:    
  # Oxilife
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_acid_pump
    name: Oxilife Säure Pumpe
    device_class: RUNNING
    address: 0x0107
    bitmask: 0x1000
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_ph_module_flow_control
    name: Oxilife pH Flow Control
    device_class: RUNNING
    address: 0x0107
    bitmask: 0x0400
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    id: oxilife_hydrolysis_flow
    name: Oxilife Hydrolysis Flow
    device_class: RUNNING
    address: 0x010D
    bitmask: 0x0008 
    register_type: read
  #Oxilife relays
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay 1 pH
    address: 0x010E
    bitmask: 0x0001
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay 2 Filtering
    address: 0x010E
    bitmask: 0x0010
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay 3 Light
    address: 0x010E
    bitmask: 0x0004
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay 4
    address: 0x010E
    bitmask: 0x0008
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay Slow Speed
    address: 0x010E
    bitmask: 0x0100
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay Medium Speed
    address: 0x010E
    bitmask: 0x0200
    device_class: POWER
    register_type: read
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Relay High Speed
    address: 0x010E
    bitmask: 0x0400
    device_class: POWER
    register_type: read
  # Relay board
  - platform: modbus_controller
    modbus_controller_id: relayboard8_with_inputs
    name:  "garten_relayboard8_input1"
    register_type: holding
    address: 0x81
  - platform: modbus_controller
    modbus_controller_id: relayboard8_with_inputs
    name:   "garten_relayboard8_input2"
    register_type: holding
    address: 0x82


switch:
  - platform: modbus_controller
    modbus_controller_id: oxilife
    name: Oxilife Aux Relay
    register_type: holding
    address: 0x010E
    bitmask: 0x0008
    write_lambda: |-
      uint16_t previous = id(oxilife_raw_relays).state;
      ESP_LOGE("main","Previous state to overwrite: = %d", previous);
      if(x)
        previous |= 0x0008;
      else
        previous &= ~(0x0008);

      ESP_LOGE("main","Previous state overwritten: = %d", previous);

      payload.push_back(0x01); // device address
      payload.push_back(0x10); // write function
      payload.push_back((uint8_t)(0x010E >> 8)); // register address high
      payload.push_back((uint8_t)(0x010E)); // register address low
      payload.push_back(0x00); // register count high
      payload.push_back(0x01); // register count low
      payload.push_back(0x02); // byte count

      payload.push_back((uint8_t)(previous >> 8)); // data high
      payload.push_back((uint8_t)(previous));      // data low
      return true;

 # filtration state: 0x0421 0 off, 1 is on
 # filtration mode: register 0x0411 
    # 0 manual
    # 1 auto
    # 2 heating
    # 3 smart
    # 4 intelligent
    # 13 backwash